Notes:
1. Circuit ground is internally isolated from chassis ground.
2. TFAULTis an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on
the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high
output indicates a transmitter fault caused by either the TX bias current or the TX output power
exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the
output is pulled to <0.8V.
3. Laser output disabled on TDIS>2.0V or open, enabled on TDIS<0.8V.
4. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Ordering Information
7.1 Example
SFP 35 24 -F 1 1SC-20
Sign |
Mean |
Description |
|||||
SFP |
Module type |
SFP=Single fiber SFP transceiver |
|||||
35 |
Center wave |
35=1310tx/1550rx |
53=1550tx/1310rx |
45=1490tx/1550rx |
54=1550tx/1490rx |
||
24 |
Transmitter Rate |
03=155M |
03=622M |
24=1.25G |
48=2.5G |
60=3.125G |
|
F |
Laser type |
F=FP |
D=DFB |
C=CWDM |
V=VCSEL |
||
1 |
Operating T |
1=0~+70℃ |
2=-40~+85℃ |
||||
2 |
DDMI |
1=NO DDM |
2=DDMI |
||||
SC |
Connector |
SC=SC |
LC=LC |
||||
20 |
Distance |
022=220M |
055=550M |
5=5KM |
10=10KM |
||
20=20KM |
40=40KM |
80=80KM |
100=100KM |
Part No. |
Wavelength |
Connector |
Temp. |
TX Power (dBm) |
RX Sens (Max.) (dBm) |
Distance |
SFP3524-F11SC-20 |
T 1310FP/R 1550 |
SC |
-20 to 70 |
-9 to-3 |
-21 |
20km |
SFP5324-D11SC-20 |
T 1550DFB/R 1310 |
SC |
-20 to 70 |
-15 to-3 |
-21 |
|
SFP5324-D11SC-40 |
T 1550DFB/R 1310 |
SC |
-20 to 70 |
-9 to-3 |
-24 |
40km |
SFP3524-D11SC-40 |
T 1310DFB/R 1550 |
SC |
-20 to 70 |
-5to-0 |
-24 |
|
SFP5424-D11SC-80 |
T 1550DFB/R 1310 |
SC |
-20 to 70 |
-3 to2 |
-26 |
80km |
SFP4524-D11SC-80 |
T 1490DFB/R 1550 |
SC |
-20 to 70 |
-3 to2 |
-26 |
Figure 2 Example SFP Host Board Schematic
Figure 3 Recommended Host Board Supply Filtering Network
Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA)
Figure 4 SFP Host Board Mechanical Layout
Figure 5 SFP Host Board Mechanical Layout (Cont.)
Figure 6 Recommended Bezel Design
REV: | A |
DATE: | August 30,2012 |
Write by: | |
Contact: | |
WEB: |