Factory wholesale Onu Gpon Media Converter - Huawei/cisco Compatible 10g Sfp+ lr 10km 10g Sfp+ Optical Module – HDV

Short Description:

Send email to us DOWNLOAD SPEC

Product Detail

Product Tags

Feedback (2)

Usually customer-oriented, and it's our ultimate focus on to be not only by far the most reliable, trustable and honest provider, but also the partner for our customers for Onu Cabinet, Onu Wifi Modem, Epon Onu Olt Price, We've been prepared to cooperate with company friends from at your home and overseas and produce a wonderful future with each other.

Factory wholesale Onu Gpon Media Converter - Huawei/cisco Compatible 10g Sfp+ lr 10km 10g Sfp+ Optical Module – HDV Detail:

Application

10GBASE-LR at 10.31Gbps
10GBASE-LW at 9.95Gbps
Other Optical Link

Absolute Maximum Ratings

Parameter	Symbol		Min	Max	Unit
Storage Temperature	TS		-40	+85	℃
Operating Temperature	TOP	Commercial level	-5	+70	℃
Supply Voltage	VCC		-0.5	+3.6	V
Voltage on Any Pin	VIN		0	VCC	V
Soldering Temperature ,Time	-			260℃, 10 S	℃,S

Operation Environment

Parameter	Symbol		Min.	Typ	Max.	Unit
Ambient Temperature	TAMB	Commercial level	0	-	70	℃
Power Supply Voltage	V CC-VEE		3.15	3.3	3.45	V
Power Dissipation					1	W
Data Rate	10GBASE-LR/ER/ZR			10.3125		Gbps

Optical Characteristics

(Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V)

Parameter				Symbol		Min.	Typ.	Max.	Units
Transmitter Section
Center Wavelength				lo		1300	1310	1320	nm
RMS Spectral Width				Dl		-	-	1	nm
Side Mode Suppression Ratio				SMSR		30			dB
Average Output Power			10km	Po		-6	-	-0	dBm
			20km			-2		+3
			40km			1		+4
Extinction Ratio				Er		3.5	-	-	dB
Dispersion Penalty								3.2	dB
Input Differential Impedance				Zin		90	100	110	Ω
Relative Intensity Noise				RIN₁₂OMA				-128	dB/Hz
Total jitter				Tj				0.28	UI(p-p)
Receiver Section
Center Wavelength				lo		1100		1610	nm
Receiver Sensitivity	10km			PIN	Rsen			-14	dBm
	20km							-14.4
	40km							-17
Receiver Overload				PIN	Rov	0.5			dBm
Return Loss						12			dB
LOS Assert				PIN	LOS_A	-25			dBm
LOS Dessert				PIN	LOS_D			-17	dBm
LOS Hysteresis						0.5		4	dB
LOS		High				2.0		VCC+0.3	V
		Low				0		0.8

Electrical Characteristics
(Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V)

Parameter		Symbol	Min.	Typ.	Max.	unit
Transmitter Section
Input Differential Impendence		Zin	90	100	110	Ohm
Data Input Swing Differential		Vin	180		1200	mV
TX Disable	Disable		2.0		Vcc	V
TX Disable	Enable		0		0.8	V
TX Fault	Assert		2.0		Vcc	V
TX Fault	Deassert		0		0.8	V
Transmit Disable Assert Time					10	uS
Receiver Section
Output differential impendence		Zout		100		Ohm
Data output Swing Differential		Vout	300		850	mV
Data output rise time(20~80%)		tr	30			ps
Data output fall time (20~80%)		tf	30			ps
Rx_LOS	Assert		2.0		Vcc	V
Rx_LOS	Deassert		0		0.8	V

Diagnostics

Parameter	Range	Accuracy	Unit	Calibration
Temperature	-5 ~ 75	±3	ºC	Internal
Voltage	0 ~ VCC	0.1	V	Internal
Bias Current	0 ~ 12	0.3	mA	Internal
Tx Power	-8 ~ +5	±1	dBm	Internal
Rx Power	-26 ~ 0	±1	dBm	Internal

EEPROM INFORMATION（A0）:

Addr	Field Size (Bytes)	Name of Field	HEX	Description
0	1	Identifier	03	SFP
1	1	Ext. Identifier	04	MOD4
2	1	Connector	07	LC
3-10	8	Transceiver	10 00 00 00 00 00 00 00	Transmitter Code
11	1	Encoding	06	64B66B
12	1	BR, nominal	67	10000M bps
13	1	Reserved	00
14	1	Length (9um)-km	00
15	1	Length (9um)	00
16	1	Length (50um)	08
17	1	Length (62.5um)	02
18	1	Length (copper)	00
19	1	Reserved	00
20-35	16	Vendor name	48 44 56 20 20 20 20 20 20 20 20 20 20 20 20 20	HDV
36	1	Reserved	00
37-39	3	Vendor OUI	00 00 00
40-55	16	Vendor PN	xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx	ASC II
56-59	4	Vendor rev	31 2E 30 20	V1.0
60-61	2	Wavelength	05 1E	1310nm
62	1	Reserved	00
63	1	CC BASE	XX	Check sum of byte 0~62
64-65	2	Options	00 1A	LOS, TX_DISABLE, TX_FAULT
66	1	BR, max	00
67	1	BR, min	00
68-83	16	Vendor SN	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00	Unspecified
84-91	8	Vendor date code	XX XX XX 20	Year, Month, Day
92-94	3	Reserved	00
95	1	CC_EXT	XX	Check sum of byte 64~94
96-255	160	Vendor specific

Pins	Name	Discription	NOTE
1	VeeT	Transmitter Ground
2	Tx Fault	Transmitter Fault Indication	1
3	Tx Disable	Transmitter Disable	2
4	MOD DEF2	Module Definition 2	3
5	MOD DEF1	Module Definition 1	3
6	MOD DEF0	Module Definition 0	3
7	RS0	Not Connected
8	LOS	Loss of Signal	4
9	RS1	Not Connected
10	VeeR	Receiver Ground
11	VeeR	Receiver Ground
12	RD-	Inv. Received Data Output	5
13	RD+	IReceived Data Output	5
14	VeeR	Receiver Ground
15	VccR	Receiver Power
16	VccT	Transmitter Power
17	VeeT	Transmitter Ground
18	TD+	Transmit Data Input	6
19	TD-	Inv. Transmit Data Input	6
20	VeeT	Transmitter Ground

1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.

2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:

Low (0~0.8V): Transmitter on

(>0.8V, <2.0V): Undefined

High (2.0~3.465V): Transmitter Disabled

Open: Transmitter Disabled

3. MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on

the host board. The pull-up voltage shall be VccT or VccR.

MOD-DEF 0 is grounded by the module to indicate that the module is present

MOD-DEF 1 is the clock line of two wire serial interface for serial ID

MOD-DEF 2 is the data line of two wire serial interface for serial ID

4. LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. In the low state, the output will be pulled to less than 0.8V.

5. These are the differential receiver output. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES.

6. These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module.

Recommended Application Circuit

Outline drawing (mm):

Ordering information :

Part No.	Wavelength	Connector	Temp.	TX Power (dBm)	RX Sens (Max.) (dBm)	Distance
SFP+-10G-L10	1310nm	LC	0~70°C	-6 to 0	-14	10km
SFP+-10G-L20	1310nm	LC	0~70°C	-1 to +3	-14.4	20km
SFP+-10G-L40	1310nm	LC	0~70°C	1 to +4	-17	40km

Contact :

REV:	A
DATE:	August 30，2012
Write by:	HDV phoelectron technology LTD
Contact:	Room703,Nanshan district science college town, Shenzhen, China
WEB:	Http://www.hdv-tech.com

Product detail pictures:

Related Product Guide:
Comprare non è più sostenibile. Per salvare il mondo dobbiamo prendere in prestito. | Second Hand Onu
Dolje skupa dječja odjeća s markom! | 1310 Sm Sfp Module

We'll make every effort and hard work to be superb and excellent, and speed up our steps for standing inside the rank of intercontinental top-grade and high-tech enterprises for Factory wholesale Onu Gpon Media Converter - Huawei/cisco Compatible 10g Sfp+ lr 10km 10g Sfp+ Optical Module – HDV , The product will supply to all over the world, such as: Doha, Tanzania, New Delhi, because of our company has been persisting in the management idea of "Survival by Quality, Development by Service, Benefit by Reputation" . We fully realize the good credit standing, the high quality products, the reasonable price and the professional services are the reason that the customers choose us to be their long-term business partner.

1ge Onu

850nm Sfp Transceiver

Fiber Optic Media Converter

Onu Gpon Wifi

Sfp Fiber Media Converter

Sfp Wdm Module

This enterprise in the industry is strong and competitive, advancing with the times and develop sustainable, we are very pleased to have a opportunity to cooperate!