Hot sale Huawei Sfp 10g Lr Transceiver - SFP-10G-SR SFP+ 10g 850nm 300m ddm SFP module – HDV Detail:
Application
- Ethernet
- Fiber Channel 8x,10x
Absolute Maximum Ratings
|
Parameter |
Symbol |
Min |
Max |
Unit |
|
|
Storage Temperature |
TS |
-40 |
+85 |
℃ |
|
|
Operating Temperature |
TOP |
Commercial level |
-20 |
+70 |
℃ |
|
industrial level |
-40 |
85 |
|||
|
Supply Voltage |
VCC |
-0.5 |
+3.6 |
V |
|
|
Voltage on Any Pin |
VIN |
0 |
VCC |
V |
|
|
Soldering Temperature ,Time |
- |
|
260℃, 10 S |
℃,S |
|
Operation Environment
|
Parameter |
Symbol |
Min. |
Typ |
Max. |
Unit |
|
|
Ambient Temperature |
TAMB |
Commercial level |
0 |
- |
70 |
℃ |
|
industrial level |
-10 |
|
85 |
|||
|
Power Supply Voltage |
V CC-VEE |
3.15 |
3.3 |
3.45 |
V |
|
|
Power Dissipation |
|
|
|
1 |
W |
|
|
Data Rate |
|
|
10.3125 |
|
Gbps |
|
Optical Characteristics
(Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V)
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Units |
|
Transmitter Section |
|||||
| Center Wavelength |
lo |
840 |
850 |
860 |
nm |
| RMS Spectral Width |
Dl |
- |
- |
0.45 |
dB |
| Average Output Power |
Po |
-5 |
- |
-1 |
dBm |
| Extinction Ratio |
Er |
3.0 |
- |
- |
dB |
| Dispersion Penalty |
|
|
|
3.9 |
dB |
| Relative Intensity Noise |
RIN12OMA |
|
|
-128 |
dB/Hz |
| Total jitter |
Tj |
IEEE 802.3ae |
|
||
|
Receiver Section |
|||||
| Center Wavelength |
lo |
|
850 |
|
nm |
| Receiver Sensitivity |
Rsen |
|
|
-11.5 |
dBm |
| Stressed Sensitivity |
Rsen |
|
|
-7.5 |
dBm |
| Receiver Overload |
Rov |
0 |
|
|
dBm |
| Return Loss |
|
12 |
|
|
dB |
| LOS Assert |
LOSA |
-25 |
|
|
dBm |
| LOS Dessert |
LOSD |
|
|
-15 |
dBm |
| LOS Hysteresis |
|
0.5 |
|
4 |
|
Electrical Characteristics
(Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V)
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
unit |
|
|
Transmitter Section |
||||||
| Input Differential Impendence |
Zin |
90 |
100 |
110 |
Ohm |
|
| Data Input Swing Differential |
Vin |
180 |
|
700 |
mV |
|
| TX Disable | Disable |
|
2.0 |
|
Vcc |
V |
| Enable |
|
0 |
|
0.8 |
V |
|
| TX Fault | Assert |
|
2.0 |
|
Vcc |
V |
| Deassert |
|
0 |
|
0.8 |
V |
|
|
Receiver Section |
||||||
| Output differential impendence |
Zout |
|
100 |
|
Ohm |
|
| Data output Swing Differential |
Vout |
300 |
|
800 |
mV |
|
| Rx_LOS | Assert |
|
2.0 |
|
Vcc |
V |
| Deassert |
|
0 |
|
0.8 |
V |
|
Maximum Supported Distances
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
unit |
|
| Fiber Type | 850nm OFLBandWidth |
|
|
|
|
|
| 62.5 um | 160MHz-km |
|
|
|
26 |
m |
| 200MHz-km |
|
|
|
33 |
m |
|
| 50 um | 400MHz-km |
|
|
|
66 |
m |
| 500MHz-km |
|
|
|
82 |
m |
|
| 2000MHz-km |
|
|
|
300 |
m |
|
Diagnostics
|
Parameter |
Range |
Accuracy |
Unit |
Calibration |
| Temperature |
-5 ~ 75 |
±3 |
ºC |
Internal |
| Voltage |
0 ~ VCC |
0.1 |
V |
Internal |
| Bias Current |
0 ~ 12 |
0.3 |
mA |
Internal |
| Tx Power |
-8 ~ 1 |
±1 |
dBm |
Internal |
| Rx Power |
-18 ~ 0 |
±1 |
dBm |
Internal |
EEPROM INFORMATION（A0）:
|
Addr |
Field Size (Bytes) |
Name of Field |
HEX |
Description |
| 0 |
1 |
Identifier |
03 |
SFP |
| 1 |
1 |
Ext. Identifier |
04 |
MOD4 |
| 2 |
1 |
Connector |
07 |
LC |
| 3-10 |
8 |
Transceiver |
10 00 00 00 00 00 00 00 |
Transmitter Code |
| 11 |
1 |
Encoding |
06 |
64B66B |
| 12 |
1 |
BR, nominal |
67 |
10000M bps |
| 13 |
1 |
Reserved |
00 |
|
| 14 |
1 |
Length (9um)-km |
00 |
|
| 15 |
1 |
Length (9um) |
00 |
|
| 16 |
1 |
Length (50um) |
08 |
|
| 17 |
1 |
Length (62.5um) |
02 |
|
| 18 |
1 |
Length (copper) |
00 |
|
| 19 |
1 |
Reserved |
00 |
|
| 20-35 |
16 |
Vendor name |
48 44 56 20 20 20 20 20 20 20 20 20 20 20 20 20 |
HDV |
| 36 |
1 |
Reserved |
00 |
|
| 37-39 |
3 |
Vendor OUI |
00 00 00 |
|
| 40-55 |
16 |
Vendor PN |
xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx |
ASC II |
| 56-59 |
4 |
Vendor rev |
31 2E 30 20 |
V1.0 |
| 60-61 |
2 |
Wavelength |
03 52 |
850nm |
| 62 |
1 |
Reserved |
00 |
|
| 63 |
1 |
CC BASE |
XX |
Check sum of byte 0~62 |
| 64-65 |
2 |
Options |
00 1A |
LOS, TX_DISABLE, TX_FAULT |
| 66 |
1 |
BR, max |
00 |
|
| 67 |
1 |
BR, min |
00 |
|
| 68-83 |
16 |
Vendor SN |
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
Unspecified |
| 84-91 |
8 |
Vendor date code |
XX XX XX 20 |
Year, Month, Day |
| 92-94 |
3 |
Reserved |
00 |
|
| 95 |
1 |
CC_EXT |
XX |
Check sum of byte 64~94 |
| 96-255 |
160 |
Vendor specific |
|
|
Pin Description:
| Pins | Name |
Discription |
NOTE |
|
1 |
VeeT |
Transmitter Ground |
|
|
2 |
Tx Fault |
Transmitter Fault Indication |
1 |
|
3 |
Tx Disable |
Transmitter Disable |
2 |
|
4 |
MOD DEF2 |
Module Definition 2 |
3 |
|
5 |
MOD DEF1 |
Module Definition 1 |
3 |
|
6 |
MOD DEF0 |
Module Definition 0 |
3 |
|
7 |
RS0 |
Not Connected |
|
|
8 |
LOS |
Loss of Signal |
4 |
|
9 |
RS1 |
Not Connected |
|
|
10 |
VeeR |
Receiver Ground |
|
|
11 |
VeeR |
Receiver Ground |
|
|
12 |
RD- |
Inv. Received Data Output |
5 |
|
13 |
RD+ |
IReceived Data Output |
5 |
|
14 |
VeeR |
Receiver Ground |
|
|
15 |
VccR |
Receiver Power |
|
|
16 |
VccT |
Transmitter Power |
|
|
17 |
VeeT |
Transmitter Ground |
|
|
18 |
TD+ |
Transmit Data Input |
6 |
|
19 |
TD- |
Inv. Transmit Data Input |
6 |
|
20 |
VeeT |
Transmitter Ground |
1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:
Low (0~0.8V): Transmitter on
(>0.8V, <2.0V): Undefined
High (2.0~3.465V): Transmitter Disabled
Open: Transmitter Disabled
3. MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on
the host board. The pull-up voltage shall be VccT or VccR.
MOD-DEF 0 is grounded by the module to indicate that the module is present
MOD-DEF 1 is the clock line of two wire serial interface for serial ID
MOD-DEF 2 is the data line of two wire serial interface for serial ID
4. LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. In the low state, the output will be pulled to less than 0.8V.
5. These are the differential receiver output. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES.
6. These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module.
Recommended Application Circuit
Outline drawing (mm):
Ordering information :
|
Part No. |
Wavelength |
Connector |
Temp. |
TX Power (dBm) |
RX Sens (Max.) (dBm) |
Distance |
|
SFP+-10G-SR |
850 |
LC |
0~70°C |
-9 to-3 |
no |
<300m |
|
SFP+-10G-SR+ |
850 |
LC |
-10~85°C |
-9 to-3 |
no |
Contact :
| REV: | A |
| DATE: | August 30，2012 |
| Write by: | HDV phoelectron technology LTD |
| Contact: | Room703,Nanshan district science college town, Shenzhen, China |
| WEB: | Http://www.hdv-tech.com |
Product detail pictures:
Related Product Guide:
United Nations General Assembly: Speech by President Emmanuel Macron (25.09.18) – France-Diplomatie | 1310 Sm Sfp Module
BVE 2019: Lawo Debuts Three New A__stage Devices; Introduces Dual Fader Bay in mc²56 Production Consoles | Second Hand Onu
To consistently enhance the management method by virtue of the rule of "sincerely, fantastic religion and top quality are the base of business development", we extensively absorb the essence of associated goods internationally, and constantly acquire new merchandise to satisfy the needs of shoppers for Hot sale Huawei Sfp 10g Lr Transceiver - SFP-10G-SR SFP+ 10g 850nm 300m ddm SFP module – HDV , The product will supply to all over the world, such as: Belize, Puerto Rico, Algeria, Till now, the goods list has been updated regularly and attracted clients from around the globe. Detailed facts is often obtained in our web-site and you'll be served with premium quality consultant service by our after-sale group. They are going to help you get comprehensive acknowledge about our products and make a satisfied negotiation. Company go to to our factory in Brazil is also welcome at any time. Hope to obtain your inquiries for any pleased co-operation.
By Muriel from Angola - 2016.09.26 12:12
This is a honest and trustworthy company, technology and equipment are very advanced and the prodduct is very adequate, there is no worry in the suppliment.
By Kitty from Finland - 2016.09.16 13:44
Products categories
Write your message here and send it to us